Lane/5000

To configure the Lane 5000 card reader for IP connectivity, you will need the following items:

  • Vbox
  • Ethernet Cable
  • Card Reader
  • Power Cord
  • Account for processing against Converge

To configure the Lane 5000 card reader for IP connectivity, complete the following steps:

For USB connectivity, refer to Configure Lane 5000 for USB Connectivity.

Configure the Card Reader to Communicate via IP

  1. Unplug then replug the power source to restart the device. The device will display a few different screens as it boots up.

  2. When the Welcome screen appears press 2, 6, 3, 4 to go to the menu settings.

    Welocme Screen

  3. Press F to see the menu

    F for Menu

  4. In the main menu screen, tap the TDA option.

    TDA

  5. Tap Configuration

    Configuration

  6. Tap Communication in the Configuration menu

    Communication

  7. Tap Select Comm. Type in the Communication menu

    Select Comm. Type

  8. Tap ETHERNET then tap the green button on the lower right of the screen

    Ethernet

Your device is now enabled to use IP.

Configure the IP Parameters

  1. Tap Ethernet Settings on the Communication menu

    Ethernet Settings

  2. Tap Connection Method on Ethernet menu

    Connection Method

  3. Tap Server and then tap green button on lower right of screen

    Server

  4. Tap Boot Protocol on Ethernet menu

    Boot Protocol

  5. Tap DHCP and then tap green button in lower right corner of screen

    DHCP

  6. Scroll down on the Ethernet menu until you see IP Port then tap IP Port.

    IP Port

  7. Confirm the value is 12000 for IP Port then press green button. If not equal to 12000, press 1, 2, 0, 0, and 0 on the keypad. If you prefer a different IP port number, enter a value between 1024 and 65536.

    IP Port 12000

  8. Press green button to save your changes if any.

Get the Assigned IP Address

  1. Press the Red (Cancel) button repeatedly until the Save and Reboot? screen appears

    Save and Reboot

  2. Tap Yes on the screen

    Save and Reboot Yes

  3. After the device reboots and the Welcome screen appears, press 0, 0, 0, 0 and scroll down to the bottom of the screen by sliding your finger up while touching the screen.

  4. Take note of the IP address assigned to the card reader. This is the IP address to use when initializing Commerce SDK.

    IP Address

    If the IP address is 0.0.0.0, check the current Ethernet port or try a different Ethernet port.

Enable SSL on the Card Reader

  1. Upon initialization, Commerce SDK will update the card reader with the required device files. HOW WILL CSDK INITIALIZE? The card reader reboots.

  2. Unplug then replug the power source to restart the device. Several screens appear as the device boots up.

  3. When the Welcome/This Lane Closed screen appears, press 2, 6, 3, 4 to go to the menu settings.

    Welcome Screen / This Lane Closed

  4. Press F button

    F for Menu

  5. In the main menu screen, tap the TDA option.

    TDA

  6. Tap Configuration

    Configuration

  7. Tap Communication

    Communication

  8. Tap Ethernet Settings

    Ethernet Settings

  9. Scroll down and tap SSL

    SSL

  10. Tap TLSv1_2 then tap the green button

    TLSv1_2

  11. Press the Red button repeatedly until the Save and Reboot? screen appears

    Save and Reboot

  12. Tap Yes to reboot device

    Save and Reboot Yes

Configure Lane 5000 for USB Connectivity

  1. Unplug then replug the power source to restart the device.

  2. When the Welcome/This Lane Closed screen appears, press the 2, 6, 3, 4.

  3. Press the F button.

  4. In the main menu screen, tap TDA on the screen.

  5. Tap Configuration on the screen.

  6. Tap Communication.

  7. Tap Select Comm. Type.

  8. Tap USB_CDC and then tap the green circle in lower right corner

  9. Press the Red (Either on keypad or screen) button repeatedly until the Save and Reboot? screen appears.

  10. Tap Yes.

    The device will restart with that the settings will take effect.